Quick View
Code produit: VAR0001471
De €799.02

Ardrox 2302 is a paint and carbon remover, it is a mixture of solvents, activators and corrosion inhibitors. This product is available to buy in various sizes.

 See Options
Panier
Skip to main content
  • basket icon Fonctionnalité de commande et de devis
  • door icon Pas de valeur minimale de commande
  • paper icon Bibliothèque de documents techniques

Ardrox 2302 Paint & Carbon Remover

Silmid P/N: VAR0001471
De €799.02 (hors TVA) €958.82 (TVA comprise)
Loading Variations

Ardrox 2302 is a paint and carbon remover, it is a mixture of solvents, activators and corrosion inhibitors. This product is available to buy in various sizes.

Data Sheets

Téléchargez dès aujourd'hui la fiche technique (TDS) du produit Ardrox 2302 Paint & Carbon Remover ainsi que la fiche de données de sécurité (SDS) du produit Ardrox 2302 Paint & Carbon Remover sur Silmid. Une fois que vous vous êtes connecté(e) ou inscrit(e), sélectionnez la taille du produit qui vous intéresse et la fiche technique sera disponible en téléchargement.

Informations produits

Ardrox 2302 is a mixture of solvents, activators and corrosion inhibitors. It consists of two layers: an upper layer oil seal to prevent evaporation of the active paint removing solvents in the lower layer.Ardrox 2302 contains no phenolic compounds, aromatic solvents or heavy metals.

Ardrox 2302 will remove a wide range of paint schemes including baked acrylics, epoxies,polyurethanes, and phenolics. It will also remove carbon or carbonaceous deposits, polymerized gum and lacquer deposits.

Application:

Ardrox 2302 is used as supplied. The total content of the container must be emptied into the tank. The recommended operating temperature range is 80 - 110°C (176 - 230°F). The product may be used for short periods at higher temperatures up to a maximum of 140°C (284°F) for removal of more obdurate finishes. In all cases, ensure, that the seal is properly maintained and all local regulations complied with, considering the 108°C (228°F) flash point of the lower layer.

  • Immersion - Immerse dry components to be stripped in Ardrox 2302 in the lower layer until paint or carbon deposits have become fully softened or detached.
  • Drain - drain components (over Ardrox 2302 tank) for approximately one minute.
  • Immersion - Immerse components in an Ardrox primary cleaner at 10% by volume at room to reduce vapors and aid subsequent pressure rinsing.
  • Pressure rinse - Pressure rinse components. The use of an Air/Water Gun or high pressure water rig is recommended.
  • Dry - Dry components thoroughly using compressed air (or an air recirculation oven at 40- 80°C / 140 - 176°F).

Approvals:

  • CFMI - CFM56
  • GE Aviation - SPM 70-80-04
  • IAE - V2500
  • Pratt Whitney - SPM 70-12-00
  • Rolls Royce - CSS 235 OMat 1/226
  • SNECMA - DMR 70-129

Conformances:

  • USAF - MIL-PRF-83936C
  • Messier/Bugatti/Dowty - PCS 2700°F
  • ASTM = ASTM F-519

Physical Chemical Properties:

  • Appearance - pale straw-colored, diphase liquid
  • Density (typical) g/ml 1.05 to 1.07 @ 20°C (68°F)
  • Flash Point (upper layer) °C (°F) 190 (374) Cleveland Open Cup
  • Flash Point (lower layer) °C (°F) 108 (228) Cleveland Open Cup

Shipping information

Livraison internationale (livraison de porte à porte) estdisponible pour certains pays dans le monde entier.Livraison sera automatiquement calculé sur le poids,l’emplacement et la nature dangereuse des marchandises.Les clients peuvent également choisir à l’usine d’organiserleur propre collection. 

Veuillez vous reporter à notre page de livraison pour plusd’informations.